Skip to content

Quality Inspector · How-to guides

Quality Inspector User Guide

Last updated October 28, 2026

Quality Inspector from Insight Works for Microsoft Dynamics 365 Business Central helps you create inspections, record measurements and observations, evaluate results, and manage the follow-up actions required by your quality processes.

Use this guide to understand the inspection lifecycle and find instructions for common tasks, including receiving inspections, production checks, sampling, inventory holds, Non-Conformance Reports, and Certificates of Analysis.

Before you begin

Quality Inspector should be configured with the templates, grades, source configurations, and test generation rules required by your processes. Users also need permissions appropriate to their inspection and Business Central responsibilities.

For configuration guidance, see Quality Inspector Setup Guide, and  Set Up and Configure Quality Inspector.

Three concepts are useful when working with inspections:

Concept Purpose
Quality Inspection Template Defines the questions, measurements, checks, and requirements for an inspection.
Test Generation Rule Determines which template applies to a Business Central record and supports the configured creation methods.
Quality Inspection Test The inspection record containing source information, recorded values, and results.

For an introduction, see Understand Quality Inspection Templates and Test Generation Rules.

Work with Quality Inspection Tests

A typical inspection process involves creating or locating the test, recording results, finishing the inspection, and completing any required follow-up.

Create an inspection manually

Use manual creation when an inspection is needed on demand.

  1. Open Quality Inspection Tests.
  2. Select Create Test.
  3. Select the template.
  4. Select the source where more than one source is available.
  5. Choose the record to inspect and any additional item-tracking filters.
  6. Select OK.

The template and generation rule must already be configured.

You can also create tests from supported source records. For example, for purchase orders, open a purchase order, select the line and from the line actions choose Create Test, or if the item is lot or serial tracked then from the item tracking lines create a test. Quality Inspector evaluates the applicable rules and uses the matching template.

Related articles:

Work with automatically created inspections

Depending on your configuration, tests can be created during receiving, production output, assembly output, warehouse movements, or scheduled processing.

Perform the normal Business Central transaction, then locate the resulting inspection using your inspection list or assigned-work process. A test can be created without opening immediately; the Show Test setting controls whether newly created tests are displayed.

Existing-test settings can also cause an earlier inspection to be reused or a retest to be created. If you expect a new test, review the related inspections before creating another manually.

Related articles:

Locate and review your inspection

Open the appropriate Quality Inspection Test and confirm its source document, item, tracking information, and quantity before recording results.

Review the assigned inspector and planned work as applicable to your process.

Related article:

Record measurements and observations

Enter the actual result in each applicable Test Value field. The field type determines whether you enter a measurement, select a choice, record text, or provide another supported value.

Quality Inspector evaluates recorded values using the configured grade conditions. Allowable values determine what can be entered; passing conditions determine whether the result meets the specification.

Where required by the inspection:

  • Record the individual sample measurements.
  • Identify the measurement tools used.
  • Add a measurement note to explain a result or observation.
  • Attach supporting documents or pictures.
  • Complete the configured signature fields.

Measurement notes are entered against individual test lines. Access to view or edit them depends on inspector permissions.

Related articles:

Review and finish the inspection

Review the recorded values and resulting grade. Grade Code identifies the inspection result; Status identifies whether the test is open or finished.

To finish an open test, select it on Quality Inspection Tests, choose Finish, and confirm.

If your process requires approval before finishing, complete the configured approval process.

Related articles:

Handle failed inspections and partially accepted quantities

Follow your organization’s disposition process when material does not meet requirements. Depending on configuration, this can involve holding inventory, moving it to quarantine, creating a purchase return, making an inventory adjustment, or creating an NCR.

When only part of the inspected quantity is rejected, use the applicable passed or failed quantity for the disposition.

For example, if 950 of 1,000 pieces are accepted, the rejected 50 pieces can be moved or returned separately. A retest is appropriate if those pieces are subsequently reworked and inspected again.

Related articles:

Create a retest

For another inspection, select the existing test on Quality Inspection Tests, choose Create Retest, and confirm.

A retest starts open so the follow-up inspection can be performed. Use it for subsequent testing, such as verification after rework or corrective action.

Related articles:

Produce inspection documentation

Use the reporting and attachment features required by your process to retain inspection records and provide supporting documentation.

Quality Inspector supports inspection reporting, Certificates of Analysis, NCR reporting, and PDF attachments. Configured workflows can create report attachments when tests finish.

Related articles:

Documentation by use case

The following sections group existing articles by common tasks. Some articles appear in more than one group because they support multiple processes.

Receiving and incoming material

Use these articles to inspect purchased material, review supplier documentation, and manage incoming inventory that requires quality review.

Production and assembly inspections

Use these articles for production-output inspections, production validation, and assembly checks.

Warehouse inspections and inventory already in stock

Use these articles when inspecting stored inventory or working with quality processes connected to put-aways and warehouse movements.

Sampling, AQL, and Skip-Lot inspections

Sampling determines how much to inspect. Skip-Lot controls which receipt or production occurrences require automatic inspection.

Use the configured sampling requirements when recording results.

Quality holds, release, and rejected material

Use these articles when inspection results control inventory availability or determine how accepted and rejected material is handled.

Non-conformance management and failure investigation

Use NCRs to document and manage quality issues requiring investigation or follow-up. Use Failure Analysis to explore patterns among failed inspections.

Customer specifications and Certificates of Analysis

A lot can pass an internal inspection and still fall outside a customer’s requirements. Use customer qualification to review suitable inventory, and customer CoAs where a separate customer-specific inspection record is required.

Notes, pictures, tools, and sign-off

Use these articles to capture the supporting evidence and approvals required by an inspection.

Periodic inspections and mobile data entry

Use these articles for recurring inspections and for recording results through the interface appropriate to the work area.

Reviewing inspection history and results

Use these references to review inspection records, individual measurements, and failure patterns.

For the complete documentation organized by business process, see Getting Started With Quality Inspector.

For configuration and version information, see Quality Inspector Setup Guide,  Set Up and Configure Quality Inspector and Release Notes: Quality Inspector.

View this article as Markdown

Still need help?

Ask other Business Central users in the Insight Works community, or send the details to the support team. Include the steps you took and any error message you saw.