Skip to content

Quality Inspector · Set up

Configure Different Receiving Inspection Requirements by Item and Vendor

Last updated September 22, 2026

Quality Inspector can apply different receiving inspection requirements to the same item depending on the vendor supplying it, allowing you to configure different receiving inspection requirements by item and vendor.

For example, an item may be purchased from four vendors:

Vendor Inspection Requirement
Vendor A No inspection required
Vendor B Sample the received quantity
Vendor C Inspect 100% of the received quantity
Vendor D Use Skip Lot to reduce inspection frequency

This can be configured using Quality Inspection Templates together with Test Generation Rules, and depending on the scenario with or without Skip-Lot rules.  The template determines how the inspection is performed, while the Test Generation Rule determines when that template applies.  This example below can be adjusted as well to work with AQL configurations and skip-lot configurations.

Create the Inspection Templates

Create the Quality Inspection Templates required for the different inspection levels.

For example:

  • RECEIVE-SAMPLE – configured to inspect a percentage, fixed sample quantity, or AQL-based sample.
  • RECEIVE-100 – configured with Sample Source = Percent of Quantity and Sample Percentage = 100.

The same template can be reused for multiple vendors when the inspection requirements are the same.

Create a Vendor and Item-Specific Receiving Rule

To apply an inspection to a specific vendor and item:

  1. Search for Quality Inspection Test Generation Rules in Business Central.
  2. Select Create Receiving Rule.
  3. Select the Quality Inspection Template to use.
  4. Enable Purchase Line as the type of receiving rule.
  5. Select Next.
  6. In Vendor No., select the vendor to which the rule applies.
  7. Select Next.
  8. In Specific Item, select the item to which the rule applies.
  9. Complete the remaining receiving-rule options and select Finish.

The resulting rule applies only when both the vendor and item filters match.

Instead of a single item, the item portion of the rule can also be filtered by Category, Inventory Posting Group, or additional advanced item fields.

Example

For item ITEM-100:

Vendor Configuration
Vendor A No vendor/item receiving rule requiring an inspection
Vendor B Vendor B + ITEM-100 → RECEIVE-SAMPLE
Vendor C Vendor C + ITEM-100 → RECEIVE-100
Vendor D Vendor D + ITEM-100 → RECEIVE-SAMPLE with a Skip Lot Rule

When ITEM-100 is received from Vendor B, Quality Inspector can create the sampling inspection.

When the same item is received from Vendor C, Quality Inspector can instead create the 100% inspection.

For Vendor A, ensure that no applicable receiving Test Generation Rule requires an inspection for that vendor/item combination.

Vendor D can use the same type of receiving inspection as Vendor B while allowing Skip Lot to determine which receipts require a test.

Configure Vendor D for Skip Lot

For this example, Vendor D will use the following sequence:

  • Test the first 2 receipts.
  • Skip the next 2 receipts.
  • Test the next receipt.
  • If the test passes, return to skipping 2 receipts.
  • If a test fails, return to testing 2 receipts.

This is a 2 Test – 2 Skip – 1 Test pattern.

Create the Skip Lot Rule

  1. Search for Quality Inspector Skip Lot Rules.
  2. Select + New.
  3. Enter a code and description, such as VENDD-2T2S1T.
  4. Set Count By to Occurrence.
  5. Set Group By to Item.
  6. Configure the lines as follows:
Step No. Create Threshold Action Type Success Step No. Fail Threshold
10 2 Test 20 1
20 2 Skip 30 1
30 1 Test 20 1

This causes the first two receipt occurrences to be tested, the next two to be skipped, and the next receipt to be tested. After the test in Step 30, the sequence returns to the skip step. A failed test returns the item to Step 10.

Assign the Skip Lot Rule to Vendor D

After creating the Skip Lot Rule:

  1. Open Quality Inspection Test Generation Rules.
  2. Locate the receiving Test Generation Rule for Vendor D + ITEM-100.
  3. Set Skip Lot Rule Code to VENDD-2T2S1T.

The receiving rule still determines that Vendor D and ITEM-100 use the selected Quality Inspection Template. The Skip Lot Rule determines whether an automatically generated inspection is created or skipped for each receipt.

Skip Lot applies to automated test generation. Manually creating a test does not advance or follow the Skip Lot sequence.

Consider Other Receiving Rules

Review existing Test Generation Rules when adding vendor-specific rules.

More than one rule may match the same purchase line. Quality Inspector evaluates matching rules according to their Sort Order and uses the first applicable template.

Place more specific vendor/item rules ahead of broader rules such as rules that apply to an entire item category or to all purchase receipts.

Vendor Qualification Status

The configuration described above determines inspection behavior through Quality Inspection Templates, Test Generation Rules, and optionally Skip Lot Rules. It does not create a separate vendor/item qualification-status value such as Approved, Sampling, 100% Inspection, or Skip Lot.

The effective inspection requirement is represented by the configuration of these rules.

References

View this article as Markdown

Still need help?

Ask other Business Central users in the Insight Works community, or send the details to the support team. Include the steps you took and any error message you saw.