Skip to content

Quality Inspector · Set up

Handle Partial Acceptance and Rejected Quantities in Quality Inspector

Last updated September 22, 2026

Quality Inspector can be used when only part of an inspected quantity is accepted, this article will work through some examples of how you could handle partial acceptance and and partial rejected quantities in Quality Inspector.

For example, suppose you receive 1,000 pieces and determine that:

  • 950 pieces are accepted
  • 50 pieces are rejected

The Quality Inspection Test can record:

  • Source Quantity (Base): 1,000
  • Pass Quantity: 950
  • Fail Quantity: 50

Quality Inspector can then use the passed or failed quantity when performing supported inventory disposition actions. This allows the accepted and rejected quantities to be handled separately without creating another inspection solely to divide the inventory.

Handle the Failed Quantity

Depending on the required process, the 50 failed pieces can be handled in several ways.

For example, you can:

  • Move the failed quantity to a quarantine or QC Hold bin.
  • Transfer the failed quantity to another location.
  • Create a purchase return for the failed quantity.
  • Create a negative inventory adjustment for the failed quantity.
  • Change item tracking information when the failed inventory must be reclassified.
  • Configure a workflow to perform the required disposition automatically when the inspection is finished.

Quality Inspector supports Failed Quantity and Passed Quantity as disposition quantity options. Therefore, a disposition can act on the 50 failed pieces rather than automatically acting on the entire 1,000-piece source quantity.

The 950 passed pieces can similarly be used as the quantity for supported disposition actions.

Example: Move the 50 Failed Pieces to a Quarantine Bin

If rejected inventory must remain available but physically separated:

  1. Finish the Quality Inspection Test with:
    • Pass Quantity = 950
    • Fail Quantity = 50
  2. Run the appropriate inventory movement action.
  3. Select Failed Quantity as the quantity to move.
  4. Specify the applicable quarantine location or bin.

This leaves the accepted inventory available for its normal process while separating the 50 rejected pieces for review or disposition.

A Business Central workflow can also automate inventory movement based on the completed inspection and its grade. Quality Inspector must have Workflow Integration enabled for Quality Inspector workflow events and responses to be available.

Example: Automatically Negate the 50 Failed Pieces

If failed material is being discarded, destroyed, or otherwise removed from inventory, Quality Inspector supports creating a Negative Adjustment from the Quality Inspection Test.

This can be performed manually from the test or automated with a Business Central workflow.

For an automated process:

  1. Open Quality Inspector Setup.
  2. Enable Workflow Integration.
  3. Create a Business Central workflow for the appropriate Quality Inspection Test event, such as the inspection being finished.
  4. Add conditions identifying the inspection result that should cause inventory to be removed.
  5. Add the Quality Inspector workflow response Create a Negative Adjustment.
  6. Configure the response to use Failed Quantity.

In this example, the negative adjustment would use the test’s Fail Quantity of 50, rather than the entire source quantity of 1,000.

Depending on the configured negative-adjustment posting behavior, Quality Inspector can create the applicable journal activity or process the adjustment according to the selected configuration.

This is useful for processes such as:

  • Destructive testing.
  • Scrapped incoming material.
  • Damaged material that will not be returned.
  • Failed material that must be written off immediately.

Example: Return the 50 Failed Pieces to the Vendor

If the rejected material is being returned rather than discarded:

  1. Finish the inspection with Pass Quantity = 950 and Fail Quantity = 50.
  2. Run the purchase return disposition.
  3. Select Failed Quantity.
  4. Create the purchase return for the rejected material.

This allows the disposition to use the 50-piece failed quantity while retaining the 950 accepted pieces.

Example: Automatically Release the 950 Passed Pieces

The same approach can be used for accepted inventory.

For example, inventory may initially be received into a QC Hold or inspection bin. A Business Central workflow can respond to a passing inspection and create the appropriate inventory movement for the accepted inventory.

Where appropriate, configure the disposition to use Passed Quantity so that the movement applies to the 950 accepted pieces.

The failed 50 pieces can remain in the QC Hold or quarantine area until a separate disposition decision is made.

When to Create a Re-test

A Re-test is intended for another inspection after the original inspection, such as following corrective action, rework, additional review, or another inspection requirement.

A re-test is not required simply because part of the original quantity passed and part failed.

For example:

Initial inspection

  • Source Quantity: 1,000
  • Pass Quantity: 950
  • Fail Quantity: 50

The 50 failed pieces can first be moved, returned, adjusted, or otherwise dispositioned.

If those 50 pieces are subsequently reworked and must be inspected again, a Re-test can then be created to record that subsequent inspection.

Re-tests Should Start Open

When Quality Inspector creates a re-test, the new test starts as Open. The previous grade and finished information are not carried forward as completed inspection results.

Therefore, if a newly created re-test immediately changes to Finished without the follow-up inspection being performed, this is not the standard Create Re-test behavior.

Review any enabled Business Central workflows, Quality Inspector workflow responses, or custom extensions that could be responding when the re-test is created.

Quality Inspector supports workflow events associated with re-tests, so configured automation can take further actions after the re-test is created.

Example Process

For a receipt of 1,000 pieces where 50 are rejected:

  1. Complete the Quality Inspection Test.
  2. Record Pass Quantity = 950 and Fail Quantity = 50.
  3. Decide how the 50 failed pieces should be handled.
  4. Use Failed Quantity for the appropriate disposition, such as:
    • Moving the 50 pieces to quarantine.
    • Creating a purchase return.
    • Creating a negative adjustment.
    • Reclassifying the inventory.
  5. Optionally use a workflow to automate the disposition based on the completed test and grade.
  6. Release or move the 950 accepted pieces using Passed Quantity where applicable.
  7. If the rejected material is later reworked or requires another inspection, create a Re-test for that subsequent inspection.

This keeps the original inspection result, the physical or financial disposition of rejected inventory, and any subsequent inspection as separate parts of the quality process.

References

Getting Started With Quality Inspector

Quality Inspector Setup

How to Place Part of a Lot On Hold in Quality Inspector

Sample Workflows for Quality Inspector: Moving Items, Initiating a Retest, and Discarding Failed Stock

Manage COA-Required Purchase Receipts with Quality Inspector

Set a Database Value in a Workflow Response

Release Notes: Quality Inspector

View this article as Markdown

Still need help?

Ask other Business Central users in the Insight Works community, or send the details to the support team. Include the steps you took and any error message you saw.