Skip to content

Quality Inspector · Set up

Quality Inspector Setup Guide

Last updated October 28, 2026

Quality Inspector from Insight Works for Microsoft Dynamics 365 Business Central lets you define what to inspect, when inspections should be created, how results are evaluated, and what happens when an inspection passes or fails.

This guide outlines the initial setup sequence and groups the supporting documentation by setup topic. Configure the topics that apply to your receiving, production, warehouse, and other quality processes.

General setup guidance

Start with one representative inspection process, such as inspecting a purchased item or recording a production check. Confirm that the correct test is created and its results are evaluated as expected before adding sampling, inventory restrictions, or automated dispositions.

A typical setup follows these steps:

  1. Install Quality Inspector from AppSource.
  2. Assign permissions for the people configuring the application, recording results, and performing transactions that generate inspections.
  3. Run the Quality Inspector Setup Wizard to establish the initial configuration.
  4. Review the major configuration pieces: company-wide settings, grades, inspection fields, templates, source configurations, and test generation rules.
  5. Configure the required quality processes, including automatic test creation, sampling, inventory controls, workflows, and NCRs.
  6. Validate each process using representative Business Central transactions.

For the implementation walkthrough, see Set Up and Configure Quality Inspector.

Before you begin

Identify where inspections are required and when they should occur. Common starting points include incoming material, production output, in-process checks, assembly output, warehouse movements, and periodic inspections.

Review the Business Central records involved in those processes, including items, locations, warehouse handling, and item tracking. Quality Inspector supports tracked and untracked inventory; processes that identify or restrict particular lots, serial numbers, or packages depend on the corresponding tracking configuration.

Review Release Notes: Quality Inspector for version compatibility and feature availability.

Initial setup wizard

Complete the Quality Inspector Setup Wizard before building your inspection processes. The wizard provides core configuration, including standard grades and source configurations used by common Business Central processes.

After completing the wizard, review the resulting configuration against your requirements. Your inspection questions, acceptance criteria, templates, and generation rules still need to reflect the processes you intend to implement.

Related articles:

Permissions and inspector access

Assign Business Central permission sets according to each user’s responsibilities. Quality Inspector provides permission sets for supervisors, data-entry users, and read-only users.

Users also need the Business Central and Insight Works permissions required for their work. Include receiving and production employees whose transactions automatically generate inspections.

Quality Inspector’s functional permissions provide additional restrictions on quality activities. These supplement Business Central permission sets.

Related article:

Company-wide settings

Open Quality Inspector Setup and review the settings that control application behaviour.

Setup topic What to review
Visibility and display Whether Quality Inspector is visible and when newly created tests should open.
Numbering The default number series for Quality Inspection Tests, with template-specific numbering where required.
Existing tests Whether to create a new test, create a retest, or reuse an existing test, and how matching tests are found.
Automation defaults Default triggers for receiving, production, assembly, and other supported processes.
Item tracking Tracking requirements before a test can be finished.
Inventory movement Batches and worksheets used for inventory disposition.
Optional features Workflow integration, sampling defaults, picture handling, and other features your process requires.

Automation settings on Quality Inspector Setup define defaults for test generation rules. Review the trigger on each applicable rule when configuring automatic test creation.

Related articles:

Inspection fields, templates, and grades

Define the questions, measurements, and checks inspectors must complete, then organize them into Quality Inspection Templates.

The main configuration pieces are:

  • Quality Inspection Fields: Reusable measurements, questions, and other data points.
  • Quality Inspection Templates: The inspection plan containing the fields and requirements for a particular inspection.
  • Grades and grade conditions: The criteria used to evaluate recorded results.

Review allowable values and passing conditions separately. Allowable values control what an inspector can enter; grade conditions determine how that value is evaluated. An inspector may need to record a measurement that is outside specification.

Related articles:

Test generation rules and source configuration

After creating a template, configure the rules that determine where it applies.

Test Generation Rules select the inspection template based on the source record and configured filters. Source Configuration defines how source records are related and how information is populated on the test.

Use the standard source configurations where they support your process. Review custom mappings when inspecting custom tables or retrieving additional related information.

Related articles:

Receiving inspection setup

For incoming material, configure the inspection template, the items or other conditions it applies to, and the receiving event that creates the test.

Include your actual receiving method in the configuration and validation. Receiving directly from a purchase order and receiving through warehouse documents can involve different source records and automation settings.

Related articles:

Production and assembly inspection setup

For manufacturing processes, configure production rules and select the event that should create the inspection. Also determine whether production must wait for a completed inspection at a defined checkpoint.

For assembly processes, configure the applicable template and generation rule for assembly output.

Related articles:

Sampling, AQL, and Skip-Lot setup

Decide how much material must be inspected and how frequently inspections are required.

Sampling determines the quantity to inspect, such as a fixed quantity, percentage, or AQL-based sample. Skip-Lot determines which receipt or production occurrences require an automatic inspection.

Configure these features according to your quality requirements, including what should happen after a failure.

Related article:

Inspection bins, inventory restrictions, and disposition

Determine how inventory should be handled while inspection is pending and after it passes or fails.

Depending on the process, this can include routing material to inspection bins, restricting selected transactions, blocking tracked inventory, or moving material after a quality decision.

Configure inspection-bin routing and transaction restrictions according to the control you need. Moving inventory into a quarantine bin does not, by itself, provide the same transaction restrictions as blocking inventory.

Related articles:

Workflows and approvals

Enable Workflow Integration on Quality Inspector Setup when Business Central workflows are part of your implementation.

Configure the events, conditions, and responses required by your process. Examples include creating retests or NCRs, moving inventory, and requiring approval before an inspection can be finished.

Related articles:

Non-Conformance Reports

If your process uses Non-Conformance Reports, configure how NCRs are created, which template they use, and who can create them.

The NCR Process Configuration Wizard supports different approaches, including a printable report from a normal test, a separate NCR created from a source document, or an NCR created from an existing inspection. Automatic NCR creation can be configured for finished, failed inspections.

Related article:

Additional setup topics

Configure these features where they are part of your inspection process:

Validate the setup

Before using the configuration in production, test each process from beginning to end.

Confirm that the intended transaction selects the correct template, populates the expected source information, and creates or reuses tests as intended. Record passing and failing results, finish the test, and verify any configured inventory restrictions, movements, approvals, or NCR creation.

Perform validation with the permissions and interface the employee will use.

For the complete documentation organized by business process, see Getting Started With Quality Inspector.

View this article as Markdown

Still need help?

Ask other Business Central users in the Insight Works community, or send the details to the support team. Include the steps you took and any error message you saw.