Skip to content

Warehouse Insight

Device columns and Ad-Hoc movement for locations without BINs

Viewing 6 posts – 1 through 6 (of 6 total)
  • Author
    Posts
  • #8540
    Terje K.

    So i have customer with simple warehouse setup. They want to move items between locations. Locations don’t have bins. When i open Ad-Hoc Move, scan item, insert qty and screen goes to Place, when i scan location code then i get error (v2.13.8908.1) The field New Bin Code of tables Item Journal Line contains a value (location code) that cannot be found in the related table (Bin).

    Why it wants me to enter bin when there is no bin mandatory on this location?

    Also i wanted to change what fields are visible in Ad-Hoc Movement page (remove bin and bin new and show location and location new). I went in BC to Device columns. Selected Event Category ADHOC MOVE. And for all lines with COL_BIN and COL_NEW_BIN i marked visibility Hidden and for COL_LOCATION and COL_NEW_LOCATION i marked visibility Any Orientation. Then in scanner i selected reload configuration but nothing happened. Ad-Hoc is not showing me location fields. I even tried to close app and log on and off. Nothing happened.

    What can be the issue that columns are not changing?

    #10028
    Terri V.
    Insight Works
    Hello Terje,
    You will need at least one Bin set up to do the Take process in moving items between Locations. The scanning of the Bin is what confirms the Location that your Device Configuration is tied to. The main reason is you don’t have someone in a different Location just start moving items around between Locations.  Once you scan the Bin, Location will default in Take mode. It would be a modification to be able to just scan Location barcodes for both Take and Place steps to take place.
    You can make columns visible on the handheld by selecting anywhere in the column header and holding until the ‘Choose Columns’ pops up. Select ‘Choose Columns’ and you can select which columns you want visible and not visible. The ‘Visible’ toggle down at bottom of screen. You can also set column width in pixels.
    Thank you,
    #10030
    Terje K.

    Hello Terri.

    Thank you for your replay. I see from another post that in wms express it is possible to use location without bins. So these functionalities are different for cloud and onprem?

    WMS Express Ad-Hoc movements without Bins – Insight Works Knowledge Base (dmsiworks.com)

    I tried to change/add columns through scanner and it worked! In what cases i should use then in BC Device columns?

    #10032
    Terri V.
    Insight Works

    Hello Terje,

    You are correct, you are able to do an Ad Hoc Movement in a Locations without Bins. You will just need to scan the Item first. It shouldn’t matter if OnPrem or Saas.

    Just a side note that Ad-Hoc Movement will not work with Directed Locations.

    The only time you would need to use the Device Columns is when the column is not available to make visible on the handheld, then you would need to go to Device Columns to make the column visible or add in a column override.

    Thank you,

    #10033
    Terje K.

    Hi Terri

    As i get error then i want to confirm. Can i move items between 2 different locations where bin is not mandatory for both of them? After scanning item it automatically goes to Place window but i cannot say what location i want to put it. When i scan location code then i get error that this Bin doesn’t exist.

    #10034
    Terje K.

    Hi Terri

    I had a Teams meeting with your college Leir and my issue was that i tried to scan location code QR code but i needed QR code where location code is combined with symbols %LOC%. So once i generated for my location PROD QR code %LOC%PROD then it worked as expected.

    Than you both very much for your help!

    With best regards,

    Terje

Viewing 6 posts – 1 through 6 (of 6 total)
  • Sign in below to reply.