---
title: "Move Product from One Bin to Another Bin Automatically in Quality Inspector"
app: "Quality Inspector"
section: "Set up"
last_updated: "2025-12-18"
url: "https://insight-works.com/kb/quality-inspector/move-product-from-one-bin-to-another-bin-automatically-in-quality-inspector/"
---

# Move Product from One Bin to Another Bin Automatically in Quality Inspector

Note: This walkthrough uses the standard Contoso data available in a demo Business Central 25 install.

Negating inventory can be used to help with destructive testing (the act of testing a sample destroys it), or simply when discarding inventory. Destructive testing can automatically post, but discarding inventory for a failure usually just creates an entry for review afterwards.

You can make negative adjustments manually and automatically. Automatic negative adjustments are used with destructive testing; automating the adjustment with automatic posting works as the test state of a pass or fail does not change the result of the product being destroyed.

 Note: A process consideration is how the product is physically discarded in the real world. For example, if the product is moved into a discard bin that is later moved or disposed of first, a movement might make sense to automate instead of immediately negating it. If the physical process is that a quality inspector immediately discards the material upon failure (a trash-style of bin close to them), creating the negative adjustment entry can also make sense.

Negative inventory adjustments are commonly used for two scenarios:

1. Destructive testing, where the act of testing a sample destroys the product being sampled.
2. Test failure, where the product is disposed immediately upon test failure.

### Prerequisites

- Use a W1-ENU-Extended base data with “Contoso” sample demo data as a baseline with the “WHITE” location, the “WRB-1002” item, and vendor “40000”.
- Ensure the Assisted Setup Wizard was run.
- Have a quality inspection test template.
- Have a quality inspection test generation rule.
- Have a quality inspection test for the WRB-1002 item with a known lot that is unblocked and available to be shipped.
- Ensure all batches are defined on the _Quality Inspection Setup_ These are not set up by default in the wizard.

### Steps

1. Create a test for a DPP location, such as “WHITE” (easiest is to trigger an automatic test based on a put-away), for a lot tracked item.
2. Navigate to the _Workflows_ page and select **New Workflow from Template**, select the appropriate workflow, and select **OK**.
3. Set the _Code_, _Description_, and _Category_ fields appropriately.
4. Select the _When Event_ field in the _Workflow Steps_ section and select **A Quality Inspection Test is Finished**.
5. Select the _On Condition_field and set to “Always”.
6. Select **+Filter**, select “Grade Code”, and set to “FAIL”.
7. Select **OK**.
8. Select the _Then Response_ field and select “Create Negative Adjustment” (_Conditions_ page opens).
9. Leave the _Source Location_ and _Source Bin_ filters blank.
10. Select _Entire Lot/Serial/Package_.

 Note: Sample Quantity is often used for destructive testing. Entire Lot is often used with sampling when the AQL indicates the lot itself fails. Failed Quantity would be more typical when testing discrete units (e.g., a lot of 100 bicycles was received, 1 was damaged in shipping, so discard only that 1).

1. Input a reason code (Optional).
2. Leave the _Source Location_ and _Bin Filters_ fields empty.
3. Select **Just Create Entries**.

 Note: Just Create Entries is the most common/typical scenario when discarding the entries, because it still requires some kind of human process to actually remove it. With destructive testing, it is usually automated because the act of testing destroys the sample being tested.

1. Close the screen.
2. Enable the Workflow.
3. Close the _Workflows_ page and locate the quality inspection test.
4. Input values to fail the test.
5. Finish the test (triggers the workflow and creates a negative adjustment item journal entry).
6. Open the warehouse or item journal batch (depending on the location) and locate the negative adjustment line in the journal.
